In case a plumbing appliance or pipe starts leaking, don’t keep waiting for your plumber. If it’s a major leakage or a burst, water may flow everywhere and cause a flood.
While most people think they’re quick responders to emergency situations, gushing water is not something easy to deal with.
Before we get to the teleporting age, it’s good to learn how to avoid plumbing problems from causing major damages to your home while waiting for a professional plumber.
Read on to learn some quick and easy DIY fixes and tricks shared by an emergency plumber.
You can try to minimize water damage before your plumber arrives. While these solutions may sound basic, they can save you a lot of money.
Regardless of how small some pipe leaks might be, you wouldn’t want the water to flood your home. If you allow leaks to remain unattended, small problems can turn out more serious than you’d think.
Luckily, there are several plumbing tools specially designed to assist in fixing plumbing leaks to avoid a disaster.
Regardless of the tool you’ll choose, the first thing you should do is turning off your home’s main shutoff valve. Then measure the circumference of the leaking pipe.
Once done, visit your nearest hardware center and buy epoxy compound for iron pipes. For other pipes, buy a pipe wrap or clamp. The epoxy should be applied directly to the leaking area.
Epoxy putty creates a temporary seal over a leakage. Wraps and clamps are even easier to use. You simply wrap or affix them around a leaking area. They can stop the leakage until you replace the pipe.
However, remember these solutions are temporary. Although they’ll give you an effective, quick fix, the foolproof method of eliminating a leakage permanently is replacing the leaking pipe with a new one.
Leaks on Pipe Joints
It’s quite tricky to fix leaks on pipe joints. They’re more challenging to fix than those on a normal pipeline. Joints usually bend at an angle, making most quick fixes ineffective.
Some fixes might even look awkward on pipe joints. Luckily, there are a few tools that are specially designed for fixing leaks on pipe joints. For instance, pipe connectors made of rubber and repair sleeves are flexible and can be easily wrapped around leaking joints.
The rubber connectors should be cut to be more effective. Thus, it’s necessary to take measurements of the pipe circumference. The connecter usually resists water when wrapped tightly around the leaking joint.
However, its effectiveness is only temporary. Repair sleeves usually work best on smaller leaks since they apply pressure on the leaking area when clamped tightly.
However, the small leak can widen with time beneath the sleeve. You can supplement these options using duct tape. However, duct tape is also a temporary fix.
Showers, bathtubs, toilets, and sinks may crack or even break accidentally. These plumbing appliances contain water all the time. Thus, you can easily panic in case your toilet tank cracks and floods the floor.
When such plumbing appliances crack, you should act quickly to avoid the leaking water from damaging your floor.
Plumber’s putty is a great solution for fixing leaks in plumbing appliances made of porcelain. You’ll simply apply putty on the inner side of the leaking area. Make sure you squeeze the putty snugly onto the leaking area.
Putty resists water and will prevent the leak for some time. Also, apply some more caulk on the exterior part of the leak to act as a secondary sealant.
Applying putty on the interior surface of the leak and caulking the exterior surface of the leak makes the fix last longer. However, both putty and caulk won’t last forever. The permanent solution is replacing the cracked appliance.
A Malfunctioning Water Heater
In case your water heating system is malfunctioning, the problem might be accumulation of sediment in the hot water tank. The sediment blocks the heater.
The heater will waste power and time when attempting to heat the water through the accumulated sediment. The heater gets strained and it’ll take longer to heat the water.
While you may have to replace the water heater, you can make it last longer by flushing the tank. The first thing you should do is turning off the power to the heater.
Next, run the hot water for around 10 minutes. Doing so will drain the hot water tank. Then turn off the water supply to the tank. Once done, attach a hose onto the tank’s drain valve. Direct the hose to a drain.
Next, turn on the water supply to the tank. Allow the valve to continue draining water from the tank through the hose until it stops looking discolored. Once the draining water looks clear, then it means that the sediment has cleared.
Whether your plumbing issue is significant or minor, it should be fixed soonest possible. If you allow a problem to remain unattended for long, it might lead to more damages and hence more expensive to fix.
Upon fixing your plumbing problem temporary, contact an expert plumber for a quick, effective, and permanent solution.
They usually have the required expertise to fix all types of plumbing problems. Thus, you’ll rest assured of the problem being fixed once and for all.